河北静电喷枪厂

喷漆的产品在使用的过程中难免会出现刮擦现象导致漆层的破坏，不过我们可以通过静电喷枪来加以修补和掩饰，下面将介绍一下静电喷枪的使用技巧。

In the process of using the spray paint, it is unavoidable that the scraping will cause the damage of the coating, but we can repair and cover it through an electrostatic spray gun. The following will introduce the skill of the use of the electrostatic spray gun.

静电喷枪补漆技巧一：握枪方法决定喷漆效果。补漆人员在使用喷枪进行补漆作业时要注意握枪的要领。喷枪是靠手掌、拇指、小指以及无名指握住的，用中指和食指来扣动扳机挤压涂料进行喷漆作业的。在使用的过程中可以根据工件的刮涂层位置及时调整握枪的方法以便提高喷涂的生产效率。

The technology of painting with electrostatic spray gun: the way of holding gun determines the effect of painting. The paint staff should pay attention to the key points when using the spray gun to do the paint job. The spray gun is held by the palm, thumb, little finger and ring finger, and the middle finger and index finger are used to pull the trigger and press the paint to spray paint. In the process of using, we can adjust the way of holding gun in time according to the position of scraping and coating, so as to improve the production efficiency of spraying.

静电喷枪补漆技巧二：确定喷枪的喷涂位置。要想达到理想的喷漆补漆效果，不仅要掌握喷枪的拿握方法，还要注意喷枪口与补漆处之间的位置。若喷枪口距离需补漆的位置过近会导致喷漆太稠，影响喷涂效果，若喷涂距离太远，则会浪费涂料。所以技术人员在使用喷枪时要注意喷枪的位置，以及对基材表面之间的距离。

Electrostatic spray gun painting skills two: determine the spray position of the spray gun. To achieve the desired paint effect, we should not only grasp the grip method of the spray gun, but also pay attention to the position between the gunpoint and the paint. If the distance between the muzzle and the paint is too close, the paint will be too thick, which will affect the spraying effect. If the spray distance is too far away, it will waste the paint. So technicians should pay attention to the location of the spray gun and the distance between the surface and the surface of the spray gun when using the spray gun.

静电喷枪补漆技巧三：找准喷枪的移动速度。速度决定成败，在使用喷枪进行补漆的过程中非常重要。如果喷枪移动的速度过快，会造成需补漆产品的漆层与原有漆层不匹配，同时也会造成颜色与预期的不一致。所以喷漆人员在移动喷枪的过程中需要找准喷枪的移动速度，以便达到理想的喷涂效果。

Electrostatic spray gun painting skills three: locate the speed of the spray gun. Speed decides success or failure. It is very important to use spray gun to make up paint. If the speed of the spray gun moves too fast, it will cause the paint layer to be mismatched with the original paint layer, and at the same time, it will also cause the color is not the same as expected. Therefore, in the process of moving the spray gun, the spray painting personnel needs to identify the moving speed of the spray gun, so as to achieve the ideal spraying effect.

静电喷枪补漆技巧四：扳机的控制。扳机是喷枪的核心部件，是喷枪的总控制中心。扳机扣的越深，液体流速就会越大。在以往的喷枪使用过程中，扳机一般都是扣死，而不是半扣。对于经验丰富的喷枪工作人员来说，在使用时可以不把扳机扣死，从而达到减少供漆量获得优质补漆效果的目的。

Electrostatic spray lacquer four: trigger control. Trigger is the core component of the spray gun, and the general control center of the spray gun. The deeper the trigger, the greater the flow of liquid. In the past, the trigger is usually buckled instead of half button. For the experienced staff of the spray gun, the trigger can not be fasten when used, so as to reduce the amount of paint supplied and achieve the purpose of high-quality paint repair.

静电喷枪补漆技巧五：衡量喷枪与工件表面的距离。喷枪补漆是一种技术性比较强的喷漆技术。在补漆的过程中要注意喷枪与需补漆产品之间的距离。若距离过近，可能会出现液体流淌的现象，从而造成补漆效果不佳现象的存在。如果补漆距离过远，则又会造成涂层效果与原有涂装不一致现象的存在。

Electrostatic spray gun painting skills five: measure the distance between the spray gun and the workpiece surface. Spray gun painting is a relatively strong technology of spray painting. In the process of painting, we should pay attention to the distance between the spray gun and the paint needed. If the distance is too close, there may be a phenomenon of liquid flowing, resulting in the phenomenon of poor paint effect. If the paint distance is too far away, it will also cause the inconsistent effect between the coating effect and the original coating.