河北静电喷枪厂

喷漆的产品在使用的过程中难免会出现刮擦现象导致漆层的破坏，不过我们可以通过静电喷枪来加以修补和掩饰，下面将介绍一下静电喷枪的使用技巧。

In the process of using paint, it is inevitable that scraping will lead to the destruction of paint layer, but we can repair and cover it by electrostatic spray gun. Next, we will introduce the skill of electrostatic spray gun.

静电喷枪补漆技巧一：握枪方法决定喷漆效果。补漆人员在使用喷枪进行补漆作业时要注意握枪的要领。喷枪是靠手掌、拇指、小指以及无名指握住的，用中指和食指来扣动扳机挤压涂料进行喷漆作业的。在使用的过程中可以根据工件的刮涂层位置及时调整握枪的方法以便提高喷涂的生产效率。

Electrostatic spray lacquer technique 1: the method of holding the gun determines the effect of the spray. The lacquer should pay attention to the main point of holding the gun when using the spray gun to make up the lacquer. The spray gun is grasped by the palm, the thumb, the small finger and the ring finger, and the middle and forefinger are used to pull the trigger coating for the spray painting. In the process of use, the method of holding the gun can be adjusted according to the position of the scraping coating of the workpiece in order to improve the production efficiency of the spraying.

静电喷枪补漆技巧二：确定喷枪的喷涂位置。要想达到理想的喷漆补漆效果，不仅要掌握喷枪的拿握方法，还要注意喷枪口与补漆处之间的位置。若喷枪口距离需补漆的位置过近会导致喷漆太稠，影响喷涂效果，若喷涂距离太远，则会浪费涂料。所以技术人员在使用喷枪时要注意喷枪的位置，以及对基材表面之间的距离。

Electrostatic spray lacquer two: determine the spraying position of the spray gun. In order to achieve the desired effect of paint and paint, not only grasp the method of holding the gun, but also pay attention to the position between the gunshot and the paint. If the distance from the nozzle of the gunshot is too close, the spray paint is too thick to affect the spray effect. If the spray distance is too far away, the paint will be wasted. So the technical personnel should pay attention to the position of the spray gun and the distance between the surface of the base material when using the spray gun.

静电喷枪补漆技巧三：找准喷枪的移动速度。速度决定成败，在使用喷枪进行补漆的过程中非常重要。如果喷枪移动的速度过快，会造成需补漆产品的漆层与原有漆层不匹配，同时也会造成颜色与预期的不一致。所以喷漆人员在移动喷枪的过程中需要找准喷枪的移动速度，以便达到理想的喷涂效果。

Electrostatic spray lacquer three: find the speed of the gun. Speed determines success or failure, and it is very important in the process of using a spray gun to make up the paint. If the speed of the spray gun is too fast, the paint layer that needs to be lacquered is not matched with the original lacquer layer, and it will also cause the difference between the color and the expected. Therefore, in the process of moving the spray gun, the spray paint personnel need to find the speed of the spray gun, in order to achieve the ideal spraying effect.

静电喷枪补漆技巧四：扳机的控制。扳机是喷枪的核心部件，是喷枪的总控制中心。扳机扣的越深，液体流速就会越大。在以往的喷枪使用过程中，扳机一般都是扣死，而不是半扣。对于经验丰富的喷枪工作人员来说，在使用时可以不把扳机扣死，从而达到减少供漆量获得优质补漆效果的目的。

Electrostatic spray lacquer four: trigger control. The trigger is the core part of the spray gun and the general control center of the spray gun. The deeper the trigger, the greater the flow of liquid. In the past, the trigger was usually buckled, not a half buckle. For the experienced staff of the spray gun, the trigger can not be fasten when used, so as to reduce the amount of paint supplied and achieve the purpose of high-quality paint repair.

静电喷枪补漆技巧五：衡量喷枪与工件表面的距离。喷枪补漆是一种技术性比较强的喷漆技术。在补漆的过程中要注意喷枪与需补漆产品之间的距离。若距离过近，可能会出现液体流淌的现象，从而造成补漆效果不佳现象的存在。如果补漆距离过远，则又会造成涂层效果与原有涂装不一致现象的存在。

Electrostatic spray lacquer five: measuring the distance between the spray gun and the surface of the workpiece. The spray lacquer of the spray gun is a highly technical spray painting technique. In the process of filling the paint, pay attention to the distance between the spray gun and the product that needs to be mended. If the distance is too close, the flow of liquid may appear, which causes the poor effect of the paint. If the distance of the paint is too far away, it will cause the existence of the coating effect and the original painting.